Даташиты

Если Вы ищете документацию на какую-либо микросхему, описание какого-либо транзистора, то в данном разделе Вы можете её скачать.

В сети

Пользователей: 137
Из них просматривают:
Аналоги: 35. Галерея: 1. Даташиты: 23. Инструкции: 1. Новости: 3. Остальное: 6. Партнёры: 1. Программы: 1. Профиль пользователя: 2. Теги: 1. Форум: 63.
Участников: 2
Гостей: 135

Google , Яндекс , далее...
Рекорд 2375 человек онлайн установлен 26.12.2015.

Партнёры


Партнёры

Новые объявления

В настоящее время нет объявлений.

Драйверы Драйверы светодиодов : MAX16834
Отправил MACTEP. Дата добавления 27.12.2012 (1660 прочтений)

High-Power LED Driver with Integrated High-Side LED
Current Sense and PWM Dimming MOSFET Driver


General Description
The MAX16834 is a current-mode high-brightness LED (HB LED) driver for boost, buck-boost, SEPIC, and high-side buck topologies. In addition to driving an n-channel power MOSFET switch controlled by the switching controller, it also drives an n-channel PWM dimming switch to achieve LED PWM dimming. The MAX16834 integrates all the building blocks necessary to implement a fixed-frequency HB LED driver with wide-range dimming control. The MAX16834 features constant-frequency peak current-mode control with programmable slope compensation to control the duty cycle of the PWM controller.
A dimming driver designed to drive an external n-channel MOSFET in series with the LED string provides wide-range dimming control up to 20kHz. In addition to PWM dimming, the MAX16834 provides analog dimming using a DC input at REFI. The programmable switching frequency (100kHz to 1MHz) allows design optimization for efficiency and board space reduction. A single resistor from RT/SYNC to ground sets the switching frequency from 100kHz to 1MHz while an external clock signal at RT/SYNC disables the internal oscillator and allows the MAX16834 to synchronize to an external clock. The MAX16834's integrated high-side current-sense amplifier eliminates the need for a separate high-side LED current-sense amplifier in buck-boost applications.
The MAX16834 operates over a wide supply range of
4.75V to 28V and includes a 3A sink/source gate driver
for driving a power MOSFET in high-power LED driver
applications. The MAX16834 is also suitable for DC-DC
converter applications such as boost or buck-boost.
Additional features include external enable/disable
input, an on-chip oscillator, fault indicator output (FLT)
for LED open/short or overtemperature conditions, and
an overvoltage protection sense input (OVP+) for true
overvoltage protection.
The MAX16834 is available in a thermally enhanced
4mm x 4mm, 20-pin TQFN-EP package and is specified
over the automotive -40°C to +125°C temperature range.

Applications
Single-String LED LCD Backlighting
Automotive Rear and Front Lighting
Projection System RGB LED Light Sources
Architectural and Decorative Lighting (MR16, M111)
Spot and Ambient Lights
DC-DC Boost/Buck-Boost Converters

Features
• Wide Input Operating Voltage Range (4.75V to 28V)
• 3000:1 PWM Dimming
• Analog Dimming
• Integrated PWM Dimming MOSFET Driver
• Integrated High-Side Current-Sense Amplifier for LED
Current Sense in Buck-Boost Converter
• 100kHz to 1MHz Programmable High-Frequency Operation
• External Clock Synchronization Input
• Programmable UVLO
• Internal 7V Low-Dropout Regulator
• Fault Output (FLT) for Overvoltage, Overcurrent,
and Thermal Warning Faults
• Programmable True Differential Overvoltage Protection
• 20-Pin TQFN-EP Package

Оценка: 0.00 (0 votes) - Оценить | Править описание | Сообщить о нерабочей ссылке | Рассказать другу | Комментарии (0)

Разное

Интересно

При замене электролитических конденсаторов, кроме соблюдения полярности, не следует значительно превышать допустимое рабочее напряжение.
Например, если конденсатор рассчитан на рабочее напряжение 16 В, то при установке нового той же емкости, но рассчитанного на напряжение 300 В после непродолжительной эксплуатации произойдет его расформовка, и емкость его значительно уменьшится.